Peugeot 3008 Key Fob Problems
Peugeot’s mid-sized 3008 SUV has a lot of positives. It’s stylish, handles well and has a big boot. But can it beat off strong competition in perhaps the most crowded area of the market?
If your Peugeot keyfob does not work It could be because it was exposed to clean or soapy tap water. You may need to take off the battery, clean it with isopropylethanol or electronic cleaner.
Dead coin battery
Peugeot key fobs have a small coin battery that powers their remote locking as well as other features. The battery has a short lifespan and can wear out over the course of years of use. A simple way to check whether the battery is faulty is to run a voltage test. Multimeters are used to measure the voltage between the plus and minus poles of the battery. This test will reveal if the battery is dead.
The receiver module could be the reason behind your key fobs not functioning after you’ve used your Peugeot 3008 a long time. The receiver module is in charge of receiving radio frequency signals sent by the key fobs, and sending them out to car systems. If the receiver module is damaged, it will not be able send commands to other modules inside the vehicle.
Another common cause of a key fob that is not working is moisture or sweat on the circuit board. This can cause short circuits, which will drain the battery and disable the feature that locks the fob’s remote. If this happens you must take your key fob to a chip level service technician to fix it.
Water damage
Water damage can be a problem in the event that you dropped your keyfob by the swimming water, washed it, or left it outside in the rain. Water is a good conductor, and it can cause a short circuit on circuit boards. It can also cause corrosion to the metal trace on the key fob as well as other components. A damaged circuit board could also cause the battery to dump its charge.
If you have an additional key fob, use it to lock/unlock the Peugeot 3008 to identify a dead coin cell battery as the cause of the issue. Another issue that can prevent your key fob from functioning properly is interference signals that interfere with the signal sent to the receiver module. These signals can come from a wide range of things that include radio transmitters near by.
If you hear sloshing sounds coming from your peugeot 207 new key programming 3008 when you drive it could be due to a blocked condensate drain for the evaporator. You can test this by blowing compressed air through the drain holes in your door. You can also use a flexible metal wire to wiggle drain holes to get rid of any dirt that has built up. The sound of sloshing can also indicate that there are air pockets in the cooling system.
Receiver module that is defective
The receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless message from the key fob to the receiver inside the car. This module can be damaged and prevent the car from accepting your key fob. Other factors that can trigger this problem include dead batteries or water damage, as well as interference with electronic devices that operate at the same frequency the key fob. In these situations an error message such as « card not detected » may appear on the display.
There are many ways to solve this issue. Try replacing the battery or reprogram the key fob. You can also start your vehicle with a spare key. If the key fob still does not work after following these steps, then it could have a faulty chip.
It is best to take out the chip and clean it using rubbing alcohol and paper towel. If the chip is fried you must purchase an entirely new one. The FB Series enclosures come with an holder for coin cells, which fits the most commonly used types of key fob batteries. They can also be personalized by using digital printing or CNC machined cutouts. If your key fob has been exposed to salty or dirty tap water, the chip might be contaminated and must be cleaned.
A malfunctioning keyless entry system
If you get « card not detected » This indicates that your car isn’t receiving a signal sent by your key fob. This can be caused by many reasons, such as the battery being weak or dead. The problem can often be resolved by pressing the start button on the key fob. In some instances, you’ll need to take the keyfob to a peugeot car key dealer for further repairs.
Examining the battery is the first step to solving the issue with a peugeot key replacement 3008 keyfob that won’t lock or unlock doors. Batteries are often the main cause of a malfunctioning fob however, there are other factors that can contribute to this issue too. This includes worn buttons, water damage, receiver module issues, and signal interference.
If you’ve recently been exposed to water and have your Peugeot key fob exposed to water that is clean it’s best to remove the battery and dry the electronic components using paper towel. You can also use isopropyl Alcohol or a cleaner for this purpose. If the fob has been exposed to soap or salty water, it’s best to replace it.
If your key fob still not working, try to reset it by disconnection of the battery with 12 volts for about 15 minutes. Then connect the negative cable first, then followed by the positive cable.